From c41ca64d075020e2d5daecb7f48da6af0ba5b512 Mon Sep 17 00:00:00 2001

From: Tuomas Tynkkynen <tuomas@tuxera.com>

Date: Wed, 8 Aug 2018 02:25:53 +0300

Subject: ARM: dts: sunxi: Don't use cd-inverted in sun8i-r40-bananapi-m2-ultra

Another user of cd-inverted seems to have crept in. Switch it away from

cd-inverted to be consistent with other sunxi boards.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

---

 arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 3 +--

 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

index c39b9169ea64..a891a387e8f1 100644

--- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

+++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

@@ -159,8 +159,7 @@

 &mmc0 {

 	vmmc-supply = <&reg_dcdc1>;

 	bus-width = <4>;

-	cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */

-	cd-inverted;

+	cd-gpios = <&pio 7 13 GPIO_ACTIVE_LOW>; /* PH13 */

 	status = "okay";

 };

-- 

cgit 1.2-0.3.lf.el7

From e5c6e693be831c1bba9b4f8f1da597fb5514deca Mon Sep 17 00:00:00 2001

From: Chen-Yu Tsai <wens@csie.org>

Date: Wed, 9 Jan 2019 23:02:55 +0800

Subject: ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix WiFi regulator

 definitions

The design of the Bananapi M2 Ultra has both DLDO1 and DLDO2 regulators

provide power to the WiFi+BT module, which is based on the Broadcom

BCM43438 or BCM43430 chip. Each regulator output from the PMIC can supply

up to 200 mA. The datasheet of the chip suggests a maximum power draw of

up to 360 mA when transmitting, thus requiring two outputs from the PMIC

to handle the load. However the device tree only references one of them,

leaving the other unused and possibly turned off.

This patch marks both as always-on, since we don't have a proper binding

to specify two regulators as "bound together". The name and constraints

of DLDO2 are also added.

Fixes: da7ac948fa93 ("ARM: dts: sun8i: Add board dts file for Banana Pi M2

		      Ultra")

Signed-off-by: Chen-Yu Tsai <wens@csie.org>

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

---

 arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 15 +++++++++++++++

 1 file changed, 15 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

index 438b7b44dab3..1a6794e63b90 100644

--- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

+++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

@@ -250,12 +250,27 @@

 	regulator-name = "vcc-wifi-io";

 };

+/*

+ * Our WiFi chip needs both DLDO2 and DLDO3 to be powered at the same

+ * time, with the two being in sync, to be able to meet maximum power

+ * consumption during transmits. Since this is not really supported

+ * right now, just use the two as always on, and we will fix it later.

+ */

+

 &reg_dldo2 {

+	regulator-always-on;

 	regulator-min-microvolt = <3300000>;

 	regulator-max-microvolt = <3300000>;

 	regulator-name = "vcc-wifi";

 };

+&reg_dldo3 {

+	regulator-always-on;

+	regulator-min-microvolt = <3300000>;

+	regulator-max-microvolt = <3300000>;

+	regulator-name = "vcc-wifi-2";

+};

+

 &reg_dldo4 {

 	regulator-min-microvolt = <2500000>;

 	regulator-max-microvolt = <2500000>;

-- 

cgit 1.2-0.3.lf.el7

From 1e5f1db4ccd8348a21da55bff82f4263000879ef Mon Sep 17 00:00:00 2001

From: Chen-Yu Tsai <wens@csie.org>

Date: Wed, 9 Jan 2019 23:02:56 +0800

Subject: ARM: dts: sun8i: r40: bananapi-m2-ultra: Add Bluetooth device node

The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side

identifies as BCM43430, while the Bluetooth side identifies as BCM43438.

The Bluetooth side is connected to UART3 in a 4 wire configuration. Same

as the WiFi side, due to being the same chip and package, DLDO1 and

DLDO2 regulator outputs from the PMIC provide overall power via VBAT and

I/O power via VDDIO. The CLK_OUT_A clock output from the SoC provides

the LPO low power clock at 32.768 kHz.

This patch enables Bluetooth on this board, and also adds the missing

LPO clock on the WiFi side. There is also a PCM connection for

Bluetooth, but this is not covered here.

The LPO clock is fed from CLK_OUT_A, which needs to be muxed on pin

PI12. This can be represented in multiple ways. This patch puts the

pinctrl property in the pin controller node. This is due to limitations

in Linux, where pinmux settings, even the same one, can not be shared

by multiple devices. Thus we cannot put it in both the WiFi and

Bluetooth device nodes. Putting it the CCU node is another option, but

Linux's CCU driver does not handle pinctrl. Also the pin controller is

guaranteed to be initialized after the CCU, when clocks are available.

And any other devices that use muxed pins are guaranteed to be

initialized after the pin controller. Thus having the CLK_OUT_A pinmux

reference be in the pin controller node is a good choice without having

to deal with implementation issues.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

---

 arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 26 +++++++++++++++++++++++

 1 file changed, 26 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

index 1a6794e63b90..c488aaacbd68 100644

--- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

+++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

@@ -102,6 +102,8 @@

 	wifi_pwrseq: wifi_pwrseq {

 		compatible = "mmc-pwrseq-simple";

 		reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */

+		clocks = <&ccu CLK_OUTA>;

+		clock-names = "ext_clock";

 	};

 };

@@ -196,6 +198,11 @@

 	status = "okay";

 };

+&pio {

+	pinctrl-names = "default";

+	pinctrl-0 = <&clk_out_a_pin>;

+};

+

 &reg_aldo2 {

 	regulator-always-on;

 	regulator-min-microvolt = <2500000>;

@@ -293,6 +300,25 @@

 	status = "okay";

 };

+&uart3 {

+	pinctrl-names = "default";

+	pinctrl-0 = <&uart3_pg_pins>, <&uart3_rts_cts_pg_pins>;

+	uart-has-rtscts;

+	status = "okay";

+

+	bluetooth {

+		compatible = "brcm,bcm43438-bt";

+		clocks = <&ccu CLK_OUTA>;

+		clock-names = "lpo";

+		vbat-supply = <&reg_dldo2>;

+		vddio-supply = <&reg_dldo1>;

+		device-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */

+		/* TODO host wake line connected to PMIC GPIO pins */

+		shutdown-gpios = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */

+		max-speed = <1500000>;

+	};

+};

+

 &usbphy {

 	usb1_vbus-supply = <&reg_vcc5v0>;

 	usb2_vbus-supply = <&reg_vcc5v0>;

-- 

cgit 1.2-0.3.lf.el7

From 0e363c61307062cd18c48e889b419fb37afb1c31 Mon Sep 17 00:00:00 2001

From: Pablo Greco <pgreco@centosproject.org>

Date: Tue, 16 Apr 2019 18:23:45 -0300

Subject: [PATCH v5 1/7] ARM: dts: sun8i: r40: bananapi-m2-ultra: Add GPIO

 pin-bank regulator supplies

The bananapi-m2-ultra has the PMIC providing voltage to all the pin-bank

supply rails from its various regulator outputs, tie them to the pio

node.

Signed-off-by: Pablo Greco <pgreco@centosproject.org>

---

 arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 6 ++++++

 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

index c488aaa..699579d 100644

--- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

+++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

@@ -201,6 +201,12 @@

 &pio {

 	pinctrl-names = "default";

 	pinctrl-0 = <&clk_out_a_pin>;

+	vcc-pa-supply = <&reg_aldo2>;

+	vcc-pc-supply = <&reg_dcdc1>;

+	vcc-pd-supply = <&reg_dcdc1>;

+	vcc-pe-supply = <&reg_eldo1>;

+	vcc-pf-supply = <&reg_dcdc1>;

+	vcc-pg-supply = <&reg_dldo1>;

 };

 &reg_aldo2 {

-- 

1.8.3.1

From 0729b4af5753b65aa031f58c435da53dbbf56d19 Mon Sep 17 00:00:00 2001

From: Rob Herring <robh@kernel.org>

Date: Thu, 13 Sep 2018 13:12:32 -0500

Subject: ARM: dts: sunxi: Fix I2C bus warnings

dtc has new checks for I2C buses. Fix the warnings in unit-addresses.

arch/arm/boot/dts/sun8i-a23-gt90h-v4.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"

arch/arm/boot/dts/sun8i-a23-inet86dz.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"

arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"

arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"

arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"

arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: missing or empty reg property

arch/arm/boot/dts/sun8i-a33-ippo-q8h-v1.2.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: missing or empty reg property

arch/arm/boot/dts/sun8i-a33-q8-tablet.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: missing or empty reg property

arch/arm/boot/dts/sun5i-a13-utoo-p66.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: I2C bus unit address format error, expected "40"

arch/arm/boot/dts/sun5i-a13-difrnce-dit4350.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: missing or empty reg property

arch/arm/boot/dts/sun5i-a13-empire-electronix-m712.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: missing or empty reg property

arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: missing or empty reg property

arch/arm/boot/dts/sun5i-a13-q8-tablet.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: missing or empty reg property

Cc: Maxime Ripard <maxime.ripard@bootlin.com>

Cc: Chen-Yu Tsai <wens@csie.org>

Signed-off-by: Rob Herring <robh@kernel.org>

Signed-off-by: Chen-Yu Tsai <wens@csie.org>

---

 arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 2 +-

 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts')

diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

index 35859d8f3267..bf97f6244c23 100644

--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

@@ -95,7 +95,7 @@

 &i2c0 {

 	status = "okay";

-	axp22x: pmic@68 {

+	axp22x: pmic@34 {

 		compatible = "x-powers,axp221";

 		reg = <0x34>;

 		interrupt-parent = <&nmi_intc>;

-- 

cgit 1.2-0.3.lf.el7

From 933ea7e9d143cee0c8c3bdc274afa69c91d91d61 Mon Sep 17 00:00:00 2001

From: Pablo Greco <pgreco@centosproject.org>

Date: Wed, 10 Apr 2019 18:59:25 -0300

Subject: [PATCH v2 1/6] ARM: dts: sun8i: v40: bananapi-m2-berry: Sort device

 node dereferences.

The device node dereferences are out of order, sort them.

Signed-off-by: Pablo Greco <pgreco@centosproject.org>

---

 arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 36 +++++++++++------------

 1 file changed, 18 insertions(+), 18 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

index bf97f62..f05cabd 100644

--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

@@ -105,6 +105,24 @@

 #include "axp22x.dtsi"

+&mmc0 {

+	vmmc-supply = <&reg_dcdc1>;

+	bus-width = <4>;

+	cd-gpios = <&pio 7 13 GPIO_ACTIVE_LOW>; /* PH13 */

+	status = "okay";

+};

+

+&mmc1 {

+	pinctrl-names = "default";

+	pinctrl-0 = <&mmc1_pg_pins>;

+	vmmc-supply = <&reg_dldo2>;

+	vqmmc-supply = <&reg_dldo1>;

+	mmc-pwrseq = <&wifi_pwrseq>;

+	bus-width = <4>;

+	non-removable;

+	status = "okay";

+};

+

 &reg_aldo3 {

 	regulator-always-on;

 	regulator-min-microvolt = <2700000>;

@@ -152,24 +170,6 @@

 	regulator-name = "vcc-wifi";

 };

-&mmc0 {

-	vmmc-supply = <&reg_dcdc1>;

-	bus-width = <4>;

-	cd-gpios = <&pio 7 13 GPIO_ACTIVE_LOW>; /* PH13 */

-	status = "okay";

-};

-

-&mmc1 {

-	pinctrl-names = "default";

-	pinctrl-0 = <&mmc1_pg_pins>;

-	vmmc-supply = <&reg_dldo2>;

-	vqmmc-supply = <&reg_dldo1>;

-	mmc-pwrseq = <&wifi_pwrseq>;

-	bus-width = <4>;

-	non-removable;

-	status = "okay";

-};

-

 &uart0 {

 	pinctrl-names = "default";

 	pinctrl-0 = <&uart0_pb_pins>;

-- 

1.8.3.1

From 8aaf8c380ea622a324de435fef9acc0491c98854 Mon Sep 17 00:00:00 2001

From: Pablo Greco <pgreco@centosproject.org>

Date: Wed, 17 Apr 2019 19:34:25 -0300

Subject: [PATCH v6 1/5] ARM: dts: sun8i: v40: bananapi-m2-berry: Add GPIO

 pin-bank regulator supplies

The bananapi-m2-berry has the PMIC providing voltage to all the pin-bank

supply rails from its various regulator outputs, tie them to the pio

node.

Signed-off-by: Pablo Greco <pgreco@centosproject.org>

---

 arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 15 +++++++++++++++

 1 file changed, 15 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

index f05cabd..27297f4 100644

--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

@@ -123,6 +123,21 @@

 	status = "okay";

 };

+&pio {

+	vcc-pa-supply = <&reg_aldo2>;

+	vcc-pc-supply = <&reg_dcdc1>;

+	vcc-pd-supply = <&reg_dcdc1>;

+	vcc-pe-supply = <&reg_eldo1>;

+	vcc-pf-supply = <&reg_dcdc1>;

+	vcc-pg-supply = <&reg_dldo1>;

+};

+

+&reg_aldo2 {

+	regulator-min-microvolt = <2500000>;

+	regulator-max-microvolt = <2500000>;

+	regulator-name = "vcc-pa";

+};

+

 &reg_aldo3 {

 	regulator-always-on;

 	regulator-min-microvolt = <2700000>;

-- 

1.8.3.1

From 8f708af45073e971ac75a43863382ece8bb4ce79 Mon Sep 17 00:00:00 2001

From: Pablo Greco <pgreco@centosproject.org>

Date: Thu, 11 Apr 2019 13:58:49 -0300

Subject: [PATCH v6 2/5] ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC

 ethernet controller

Just like the Bananapi M2 Ultra, the Bananapi M2 Berry has a Realtek

RTL8211E RGMII PHY tied to the GMAC.

The PMIC's DC1SW output provides power for the PHY, while the ALDO2

output provides I/O voltages on both sides.

Signed-off-by: Pablo Greco <pgreco@centosproject.org>

---

 arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 23 +++++++++++++++++++++++

 1 file changed, 23 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

index 27297f4..0dfde58 100644

--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

@@ -50,6 +50,7 @@

 	compatible = "sinovoip,bpi-m2-berry", "allwinner,sun8i-r40";

 	aliases {

+		ethernet0 = &gmac;

 		serial0 = &uart;;

 	};

@@ -92,6 +93,22 @@

 	status = "okay";

 };

+&gmac {

+	pinctrl-names = "default";

+	pinctrl-0 = <&gmac_rgmii_pins>;

+	phy-handle = <&phy1>;

+	phy-mode = "rgmii";

+	phy-supply = <&reg_dc1sw>;

+	status = "okay";

+};

+

+&gmac_mdio {

+	phy1: ethernet-phy@1 {

+		compatible = "ethernet-phy-ieee802.3-c22";

+		reg = <1>;

+	};

+};

+

 &i2c0 {

 	status = "okay";

@@ -145,6 +162,12 @@

 	regulator-name = "avcc";

 };

+&reg_dc1sw {

+	regulator-min-microvolt = <3000000>;

+	regulator-max-microvolt = <3000000>;

+	regulator-name = "vcc-gmac-phy";

+};

+

 &reg_dcdc1 {

 	regulator-always-on;

 	regulator-min-microvolt = <3000000>;

-- 

1.8.3.1

From 1d4425d5ee921a8ec63000b9544b5098a80c94fe Mon Sep 17 00:00:00 2001

From: Pablo Greco <pgreco@centosproject.org>

Date: Thu, 11 Apr 2019 14:00:05 -0300

Subject: [PATCH v6 3/5] ARM: dts: sun8i: v40: bananapi-m2-berry: Enable HDMI

 output

This patch adds the hdmi nodes to the Bananapi M2 Berry, the same way it

was done to the Bananapi M2 Ultra

Signed-off-by: Pablo Greco <pgreco@centosproject.org>

---

 arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 29 +++++++++++++++++++++++

 1 file changed, 29 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

index 0dfde58..1f4f51f9 100644

--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

@@ -58,6 +58,17 @@

 		stdout-path = "serial0:115200n8";

 	};

+	connector {

+		compatible = "hdmi-connector";

+		type = "a";

+

+		port {

+			hdmi_con_in: endpoint {

+				remote-endpoint = <&hdmi_out_con>;

+			};

+		};

+	};

+

 	leds {

 		compatible = "gpio-leds";

@@ -88,6 +99,10 @@

 	};

 };

+&de {

+	status = "okay";

+};

+

 &ehci1 {

 	/* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */

 	status = "okay";

@@ -109,6 +124,16 @@

 	};

 };

+&hdmi {

+	status = "okay";

+};

+

+&hdmi_out {

+	hdmi_out_con: endpoint {

+		remote-endpoint = <&hdmi_con_in>;

+	};

+};

+

 &i2c0 {

 	status = "okay";

@@ -208,6 +233,10 @@

 	regulator-name = "vcc-wifi";

 };

+&tcon_tv0 {

+	status = "okay";

+};

+

 &uart0 {

 	pinctrl-names = "default";

 	pinctrl-0 = <&uart0_pb_pins>;

-- 

1.8.3.1

From 6191156685f9b94b87a370d82e642671104f504c Mon Sep 17 00:00:00 2001

From: Pablo Greco <pgreco@centosproject.org>

Date: Thu, 11 Apr 2019 14:03:54 -0300

Subject: [PATCH v6 4/5] ARM: dts: sun8i: v40: bananapi-m2-berry: Enable AHCI

Just like the Bananapi M2 Ultra, enable the ahci controller and

the two regulators needed to activate it.

Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

Signed-off-by: Pablo Greco <pgreco@centosproject.org>

---

 arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 18 ++++++++++++++++++

 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

index 1f4f51f9..461683c 100644

--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

@@ -99,6 +99,12 @@

 	};

 };

+&ahci {

+	ahci-supply = <&reg_dldo4>;

+	phy-supply = <&reg_eldo3>;

+	status = "okay";

+};

+

 &de {

 	status = "okay";

 };

@@ -233,6 +239,18 @@

 	regulator-name = "vcc-wifi";

 };

+&reg_dldo4 {

+	regulator-min-microvolt = <2500000>;

+	regulator-max-microvolt = <2500000>;

+	regulator-name = "vdd2v5-sata";

+};

+

+&reg_eldo3 {

+	regulator-min-microvolt = <1200000>;

+	regulator-max-microvolt = <1200000>;

+	regulator-name = "vdd1v2-sata";

+};

+

 &tcon_tv0 {

 	status = "okay";

 };

-- 

1.8.3.1

From c8fbe63299222c29c721816939a8bb12eb77c2ac Mon Sep 17 00:00:00 2001

From: Pablo Greco <pgreco@centosproject.org>

Date: Thu, 11 Apr 2019 14:05:06 -0300

Subject: [PATCH v6 5/5] ARM: dts: sun8i: v40: bananapi-m2-berry: Add Bluetooth

 device node

The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side

identifies as BCM43430, while the Bluetooth side identifies as BCM43438.

The Bluetooth side is connected to UART3 in a 4 wire configuration. Same

as the WiFi side, due to being the same chip and package, DLDO1 and

DLDO2 regulator outputs from the PMIC provide overall power via VBAT and

I/O power via VDDIO. The CLK_OUT_A clock output from the SoC provides

the LPO low power clock at 32.768 kHz.

This patch enables Bluetooth on this board, and also adds the missing

LPO clock on the WiFi side. There is also a PCM connection for

Bluetooth, but this is not covered here.

The LPO clock is fed from CLK_OUT_A, which needs to be muxed on pin

PI12. This can be represented in multiple ways. This patch puts the

pinctrl property in the pin controller node. This is due to limitations

in Linux, where pinmux settings, even the same one, can not be shared

by multiple devices. Thus we cannot put it in both the WiFi and

Bluetooth device nodes. Putting it the CCU node is another option, but

Linux's CCU driver does not handle pinctrl. Also the pin controller is

guaranteed to be initialized after the CCU, when clocks are available.

And any other devices that use muxed pins are guaranteed to be

initialized after the pin controller. Thus having the CLK_OUT_A pinmux

reference be in the pin controller node is a good choice without having

to deal with implementation issues.

Signed-off-by: Pablo Greco <pgreco@centosproject.org>

---

 arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 38 +++++++++++++++++++++++

 1 file changed, 38 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

index 461683c..15c22b0 100644

--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

@@ -96,6 +96,8 @@

 	wifi_pwrseq: wifi_pwrseq {

 		compatible = "mmc-pwrseq-simple";

 		reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */

+		clocks = <&ccu CLK_OUTA>;

+		clock-names = "ext_clock";

 	};

 };

@@ -172,6 +174,8 @@

 };

 &pio {

+	pinctrl-names = "default";

+	pinctrl-0 = <&clk_out_a_pin>;

 	vcc-pa-supply = <&reg_aldo2>;

 	vcc-pc-supply = <&reg_dcdc1>;

 	vcc-pd-supply = <&reg_dcdc1>;

@@ -233,12 +237,27 @@

 	regulator-name = "vcc-wifi-io";

 };

+/*

+ * Our WiFi chip needs both DLDO2 and DLDO3 to be powered at the same

+ * time, with the two being in sync, to be able to meet maximum power

+ * consumption during transmits. Since this is not really supported

+ * right now, just use the two as always on, and we will fix it later.

+ */

+

 &reg_dldo2 {

+	regulator-always-on;

 	regulator-min-microvolt = <3300000>;

 	regulator-max-microvolt = <3300000>;

 	regulator-name = "vcc-wifi";

 };

+&reg_dldo3 {

+	regulator-always-on;

+	regulator-min-microvolt = <3300000>;

+	regulator-max-microvolt = <3300000>;

+	regulator-name = "vcc-wifi-2";

+};

+

 &reg_dldo4 {

 	regulator-min-microvolt = <2500000>;

 	regulator-max-microvolt = <2500000>;

@@ -261,6 +280,25 @@

 	status = "okay";

 };

+&uart3 {

+	pinctrl-names = "default";

+	pinctrl-0 = <&uart3_pg_pins>, <&uart3_rts_cts_pg_pins>;

+	uart-has-rtscts;

+	status = "okay";

+

+	bluetooth {

+		compatible = "brcm,bcm43438-bt";

+		clocks = <&ccu CLK_OUTA>;

+		clock-names = "lpo";

+		vbat-supply = <&reg_dldo2>;

+		vddio-supply = <&reg_dldo1>;

+		device-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */

+		/* TODO host wake line connected to PMIC GPIO pins */

+		shutdown-gpios = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */

+		max-speed = <1500000>;

+	};

+};

+

 &usbphy {

 	usb1_vbus-supply = <&reg_vcc5v0>;

 	status = "okay";

-- 

1.8.3.1